秋月のUSBシリアル変換モジュールを使う。
蓋を開けて端子を確認。
左から順にVcc, GND, TX, RXになっていた。(LEDを当てて一番明るく光るところがVcc)
シリアル通信設定は115200-8-N-1。
TBS bootloader V1.0 Build24362 for DSL2730U(Jul 19 2013-18:09:56) DRAM: 32 MB Flash: SPI MX25L6405D size=8M id=0x00c22017 IP: 192.168.1.1 MAC: c0:a0:bb:ad:61:41 Hit Space or Enter key to stop autoboot: 0 Checking ethernet link state... DOWN! Request for massive upgrade...Timed out! Checking version 1 image... First image OK Uncompress linux from 0x80600000 to 0x80010000... OK! Booting the kernel ... Linux version 2.6.30.9 (liuyunbing@soft) (gcc version 4.4.6 (Realtek RSDK-1.5.6p2) ) #245 Fr i Jul 19 18:22:19 CST 2013 CPU revision is: 0000dc02 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 02000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,115200 mem=32M root=31:2 mtdparts=rtl8676_spiflash:196608 (boot),1520128(kernel),2703360(rootfs),-(data) icache: 16kB/32B, dcache: 8kB/32B, scache: 0kB/0B NR_IRQS:128 PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 24400k/32768k available (3776k kernel code, 8368k reserved, 877k data, 120k init, 0k highmem) Calibrating delay loop... 458.75 BogoMIPS (lpj=2293760) Mount-cache hash table entries: 512 IMEM section size = 0x858c net_namespace: 796 bytes NET: Registered protocol family 16 bio: create slab <bio-0> at 0 SCSI subsystem initialized Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc. NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 NET: Registered protocol family 27 netlog: listening on port 4660 squashfs: version 4.0 (2009/01/31) Phillip Lougher NTFS driver 2.1.29 [Flags: R/W]. fuse init (API version 7.11) msgmni has been set to 47 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 13) is a 16550A Driver 'sd' needs updating - please use bus_type methods SPI probe: Found SPI flash MX25L6405D[ID:0xc22017] with 8M bytes! 4 cmdlinepart partitions found on MTD device rtl8676_spiflash Creating 4 MTD partitions on "rtl8676_spiflash": 0x000000000000-0x000000030000 : "boot" 0x000000030000-0x0000001a3200 : "kernel" mtd: partition "kernel" doesn't end on an erase block -- force read-only 0x0000001a3200-0x000000437200 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x000000437200-0x000000800000 : "data" mtd: partition "data" doesn't start on an erase block boundary -- force read-only PPP generic driver version 2.4.2 NET: Registered protocol family 24 IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. RTL8192C/RTL8188C driver version 1.1 (2010-03-31/2012-04-09) =====>>INSIDE rtl8192cd_init_one <<===== vendor_deivce_id=819110ec Wlan MACAddress: c0:a0:bb:ad:61:4a =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== Wlan MACAddress: c0:a0:bb:ad:61:4b =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== Wlan MACAddress: c0:a0:bb:ad:61:4c =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== Wlan MACAddress: c0:a0:bb:ad:61:4d =====>>EXIT rtl8192cd_init_one <<===== =====>>INSIDE rtl8192cd_init_one <<===== Wlan MACAddress: c0:a0:bb:ad:61:4e =====>>EXIT rtl8192cd_init_one <<===== val=5 val=c6 _ Probing RTL8186 10/100 NIC-kenel stack size order[2]... chip name: 8196B, chip revid: 0 NOT YET Set threshold idx 0 Set threshold idx 1 vport1 added. vid=9 Member port 0x2... nas0 added. vid=8 Member port 0x1... vport2 added. vid=9 Member port 0x4... vport3 added. vid=9 Member port 0x8... vport4 added. vid=9 Member port 0x10... [peth0] added, mapping to [nas0]... TBS button driver for rtl8676 initialized Mirror/redirect action on u32 classifier Performance counters on input device check on Actions configured nf_conntrack version 0.5.0 (512 buckets, 2048 max) xt_time: kernel timezone is -0000 Allocate memory success!. The phy mem addr=01e5a000, size=4096 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_conenat_init for cone nat nf_conntrack TCP cubic registered Realtek SD2-FastPath v1.00beta_2.4.26-uc0 /proc/FastPath created Realtek MCast FastPath /proc/mc_FastPath created NET: Registered protocol family 10 lo: Disabled Privacy Extensions ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions ip6tnl0: Disabled Privacy Extensions NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered ratm: RTL8670 SAR v0.0.2 (Jun 17, 2003) /proc/AUTO_PVC_SEARCH created 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 120k freed init started: BusyBox v1.6.1 (2013-07-19 18:23:03 CST) multi-call binary starting pid 161, tty '/dev/console': '/etc/init.d/rcS' @@@@@@@Welcome to TBS System@@@@@@@ mount: mounting /dev/mtdblock3 on /usr/local/ct failed mount: mounting none on /proc/bus/usb failed Loading led modules TBS leds core driver initialized Register led device for rtl8676: 1 2 4 5 6 15 16 17 18 7 8 9 10 11 12 13 14 21 23 24 =============Begin Load Modules============== modprobe usb-storage modprobe: module usb-storage not found modprobe: failed to load module usb-storage insmod: usb-storage.ko: no module by that name found modprobe usblp modprobe: module usblp not found modprobe: failed to load module usblp insmod: usblp.ko: no module by that name found modprobe usbserial modprobe: module usbserial not found modprobe: failed to load module usbserial insmod: usbserial.ko: no module by that name found =============End Load Modules================ /etc/init.d/network.rc: line 60: cannot create /proc/net/drop_conntracks: nonexistent direct ory *** TBS ver:24362, compile time:Jul 19 2013,18:31:16 *** ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCSIFHWADDR: No such device ifconfig: SIOCGIFFLAGS: No such device Cannot set VPORT: No such device starting pid 550, tty '/dev/ttyS0': '/bin/sh' / $ adsl_anxm_ok adsl_anxm_ok Wed May 23 00:00:00 UTC 2012 gSocObcIntBit=2462390000 remove REG32(0xb8000114)=0x1400 InitAdslMode.... InitAdsl inter_system.sachemIntSource=7 867x ver = N, (0412 ver)=0x62390000, (ver)=0x2e00 RTNETLINK answers: Cannot assign requested address SachemAccess::reset() 2684d started PVC Number = 8. Set Desc number per VC = 126 Creat Interface = 2684ctl -t 0 -c nas1 -e 1 -q ubr,aal5:pcr=0 -a 0.0.35 --- 4bit Rx_in read = 0x373b, 2bit Rx_in read =0x408 , DDRuse=0 AFE_ver=0x687 8676(>M) + 6256/6257 decide use DDR mode Interface "nas1" created sucessfully optarg : ubr,aal5:pcr=0 applying workaround...done device nas1 entered promiscuous mode VNET: Setting underlying device(nas1) to promiscious mode. eth4 set netif mac to: c0:a0:bb:ad:61:41 ADDRCONF(NETDEV_UP): vport4: link is not ready eth3 set netif mac to: c0:a0:bb:ad:61:41 ADDRCONF(NETDEV_UP): vport3: link is not ready eth2 set netif mac to: c0:a0:bb:ad:61:41 ADDRCONF(NETDEV_UP): vport2: link is not ready br0 set netif mac to: c0:a0:bb:ad:61:41 SachemAccess::reset() ADDRCONF(NETDEV_UP): vport1: link is not ready Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. device vport4 entered promiscuous mode device vport3 entered promiscuous mode device vport2 entered promiscuous mode device vport1 entered promiscuous mode device wlan0 entered promiscuous mode device wlan0-vap0 entered promiscuous mode device wlan0-vap1 entered promiscuous mode device wlan0-vap2 entered promiscuous mode WLAN Init : InternetGatewayDevice.LANDevice.1.WLANConfiguration.1. iptables: Bad rule (does a matching rule exist in that chain?). Interface doesn't accept private ioctl... set_mib (89F1): Operation not permitted Interface doesn't accept private ioctl... set_mib (89F1): Operation not permitted Interface doesn't accept private ioctl... set_mib (89F1): Operation not permitted Interface doesn't accept private ioctl... set_mib (89F1): Operation not permitted killall: iwcontrol: no process killed Undefined state... using AP mode as default val=4 val=c6 br0: port 5(wlan0) entering learning state killall: mini_upnpd: no process killed stProcInfo.ucExecCount:9 br0: port 5(wlan0) entering forwarding state nf_conntrack_l2tp version 3.1 loaded nf_conntrack_ipsec loaded ch:1 cca=2, fa:3, rx_count:0, rx_count_40M:0 ch:2 cca=2, fa:1, rx_count:0, rx_count_40M:0 ch:3 cca=8, fa:5, rx_count:0, rx_count_40M:0 ch:4 cca=127, fa:144, rx_count:0, rx_count_40M:0 ch:5 cca=2, fa:2, rx_count:0, rx_count_40M:1 ch:6 cca=11, fa:11, rx_count:0, rx_count_40M:0 ch:7 cca=9, fa:9, rx_count:0, rx_count_40M:2 ch:8 cca=126, fa:127, rx_count:0, rx_count_40M:2 ch:9 cca=49, fa:29, rx_count:3, rx_count_40M:16 ch:10 cca=22, fa:11, rx_count:5, rx_count_40M:4 ch:11 cca=7, fa:1, rx_count:6, rx_count_40M:1 ch:12 cca=6, fa:0, rx_count:6, rx_count_40M:0 ch:13 cca=29, fa:21, rx_count:2, rx_count_40M:0 ch1,10,ch2,18,ch3,38,ch4,261,ch5,176,ch6,216,ch7,287,ch8,461,ch9,436,ch10,436,ch11,423,ch12, 373,ch13,333, ip6tables: No chain/target/match by that name. RTNETLINK answers: Invalid argument We have an error talking to the kernel iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). killall: dproxy: no process killed Load DNS is Fake mode = 0!! /usr/bin/wscd -start -c /var/wscd-wlan0.conf -w wlan0 -fi /var/wscd-wlan0.fifo -debug [wan] get InternetGatewayDevice.WANDevice.2.WANConnectionDevice. error